SERVICES RATES

We mill trees from your forest project to final form for beams, decking, fencing, flooring, slab-form to furniture grade, our location or yours.

We stay onsite to get the job done!

Production Milling in ALL weather conditions!

We are Fully Insured

For Government & Municipal agencies; we have our EIN, DUNNS# and CCR# to expedite your purchase order & fulfill your onsite milling needs.

The operator's only responsibility is to run the Sawmill(s) for greater production. It is your responsibility to have at least two workers available to offload lumber as well as a forklift or tractor to move logs onto our mill. ***For the hydraulic mill a person is needed to assist the operator guide the mill through the log.

Our location -

Wood-mizer Computerized sawmilling service

Operator: $65.00 an hour with a 2 hr. minimum when you bring your logs to our location in Klamath Falls, Oregon. Additional charges may apply for a crew to off-load the logs & load lumber onto your truck. MAP

Hydraulic chainsaw slab milling service:

Operator $100.00 an hour with your assistance, $130 for two person team without your assistance.

Your location -

Computerized Wood-mizer Mobile sawmilling service:

Operator: 85.00 an hour (within Klamath County)
***4 hr. min. within Klamath County

Operator: 100.00 an hour (outside Klamath County), $130 for two person team without your assistance.
***8 hour minimum within 100 miles
***24 hour minimum outside 100 miles, includes travel & lodging fees

Hydraulic chainsaw slab milling service:

Operator $100.00 an hour with your assistance, $130 for two person team without your assistance.

***We do not charge a trip fee at this time so as soon as we arrive onsite our hourly rate begins.

We are willing to travel the west coast to serve our clients.

Other Fees:

For the Wood-mizer Sawmilling service:
$15.00 re-sharpening fee for all blades used onsite
$25.00 fee for all damaged blades that cannot be re-sharpened

For the Hydraulic chainsaw slab milling service:
Sharpening fee per blade used: $20.00
Damaged chains: $50.00

SERVICE INFORMATION

Our Computerized Wood-mizer sawmill can mill logs up to 20.6 feet long & from 8” to 36” in diameter. The band is 1/16th inch thickness, producing up to 30% more lumber than a circular saw blade mill.

By using our services, you save the costs of hauling logs to a mill and the lumber back to your property or jobsite. You receive all your lumber and can adjust your cut lists as you monitor our production. We can do some hand moving of logs at the mill site when a forklift or loader is not available.

Save costs by trimming large logs over 32” before our mill arrives or we will trim logs to fit our mill at our hourly rate and by cutting all limbs flush with the bark or we will have to use our chainsaw to cut limbs flush at our hourly rate, no 45 degree cuts will be accepted. YOUR crew handles all logs & stacks all lumber & cap cuts. The sawdust will be piled next to the mill or placed in cans when provided. Clean up is done after each log is milled for safety. We will leave all cap cuts whole or help you cut them into stickers for stacking to dry your lumber or cut for firewood. We charge $0.35 a bf for 2 inch thickness or greater or $0.45 a bf when less than 2 inches or under per cut with a volume of over 10,000 bf. and the log size at a minimum of 12” - 36”.

***Jobsite conditions are considered before a board foot price is given.

Any log less than 8ft long, over 30” in diameter or under 10” in diameter takes longer to mill & cannot be considered in the bf price structure. We will do very small or very large log projects by hourly rate only!

To save time & your cost, please have all log preparation completed before we arrive at your site.

We can cut at a production of 350 bf to 500 bf per hour when you provide two or more people & equipment to handle all the wood and the jobsite is flat with enough room to accommodate our mill & truck.

Your logs need to be in one central location or we will move the mill at our hourly rate. The logs are to be a minimum of 9 ft. to a maximum of 20’ 6” & all limbs cut flat to bark, no 45 degree cuts. The pile of logs needs to be centered with the trunk (butt ends) to one side note: the sawmill’s forklift faces the driver’s side of the truck. NOTE: Log Owner is responsible for all blade damage caused by any foreign objects (dirt, paint, nails, metallic objects, bolts, wire, rocks, bullets, moss, etc.) in or on logs.

To reduce the blade damage, it is recommended that you use a metal detector on urban or farm trees.

There is a fee $10.00 sharpening fee per blade and a $25.00 fee for each damaged blade. Removal of these objects saves you the cost of damaged blades.

NOTE: Rates are subject to change.